Stove & cooktop
A burner that won't light or an element that stays cold puts the whole kitchen on hold. We service gas, electric, and induction cooktops across the city.
What we service
Open every day
7:00 AM – 11:00 PM
95% one-trip fixes
Common parts on board
90-day warranty
Parts and labor covered
Price before work
Approved by you first
Symptoms we see
Cooktops give clear signals when something's failing. The trick is reading them correctly before parts get replaced.
A dirty or cracked igniter, or moisture in the burner cap. Continuous clicking after the flame catches usually means the igniter switch is stuck.
The element itself, the infinite switch behind the knob, or a burned receptacle block. All three are common and all three test differently.
A failed induction coil or power board. Sometimes it's the cookware, so we verify with a known-compatible pan before quoting anything.
Blocked burner ports or an air shutter out of adjustment. Yellow flame means incomplete combustion, which we treat as a safety issue, not a cosmetic one.
Infinite switches wear out and stop regulating. The burner ends up either full blast or off, with nothing usable in between.
Stop using it and call us. A loose fitting or failing valve needs a licensed technician, and we treat these calls as urgent.
How we work
We test each burner or zone independently, check the switches under load, and inspect the wiring behind the control panel. Cooktops share circuits, so a fault in one zone often explains odd behavior in another.
Gas work stays with our licensed technicians. We pressure-check connections after any gas repair and won't hand a range back until the flame pattern is clean and stable.

Error codes
Cooktops and ranges throw fewer codes than ovens, but the ones they do show are worth knowing. Here's what turns up most around Fort Worth.
| Code | Brand | What it usually points to |
|---|---|---|
| F1 / F2 | GE Profile / Whirlpool | Control board or keypad fault on ranges with electronic touch controls. |
| E1 / E2 | Samsung / LG | Element or sensor fault on induction and radiant tops. The zone shuts itself down. |
| E0 / U0 | Samsung | No pan detected on an induction zone, or cookware that isn't magnetic enough to couple. |
| F3 / F4 | Whirlpool / Maytag | Surface element sensor open or shorted, common on glass radiant cooktops. |
| E5 / E6 | Bosch / Thermador | Overheating protection on induction electronics, often from blocked ventilation beneath the top. |
| F7 | Whirlpool / KitchenAid | Stuck key or shorted membrane on the control panel. |
| dU | LG | Control lock engaged. Not a fault, but it stops burners responding until cleared. |
| E8 / E9 | Frigidaire / Electrolux | Power board or relay fault affecting one or more zones. |
Control board or keypad fault on ranges with electronic touch controls.
Element or sensor fault on induction and radiant tops. The zone shuts itself down.
No pan detected on an induction zone, or cookware that isn't magnetic enough to couple.
Surface element sensor open or shorted, common on glass radiant cooktops.
Overheating protection on induction electronics, often from blocked ventilation beneath the top.
Stuck key or shorted membrane on the control panel.
Control lock engaged. Not a fault, but it stops burners responding until cleared.
Power board or relay fault affecting one or more zones.
Induction electronics sit right under the glass and need airflow. A cooktop installed tight against a drawer or insulation will keep throwing overheat codes until the ventilation is corrected.
Brands
Everyday four-burner ranges through professional Wolf and Thermador tops. We keep igniters, elements, and switches for the cooktops in local kitchens.
Service area
Cooktop and range calls across Fort Worth, with gas issues moved to the front of the queue because they don't wait.
We're based here
2515 NE 36th St #18, Fort Worth, TX 76111, USA
Open every day, 7:00 AM – 11:00 PM.
ZIP codes we cover
Reviews
Front burner clicked nonstop and never lit. He cleaned the igniter, replaced the switch, and it fires instantly now. In and out in an hour.
One induction zone stopped recognizing pans. He tested the coil, confirmed the board, and had the part the next morning. Kept me posted the whole time.
Smelled gas near the range and he came out that evening. Found a loose fitting, tightened and pressure-tested it, then checked every burner. Real peace of mind.
Book a repair
Send your details and we'll ring you back to set a same-day or next-morning slot. In a hurry? Just call.
How it works
Working hours
Every day: 7:00 AM – 11:00 PM
Call us directly
(817) 330-5698Share a few details and we'll follow up shortly.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Your request has been sent. We'll call you back shortly to confirm your visit.